Cars/Motorcycles, Home

How to use ceramic tiles on a garage floor

Garage tiles

Image via: Pexels

Tiles on the garage floor are by no means an exaggerated measure. This flooring is durable, durable and easy to clean, which is why you can use ceramic tiles on a garage floor. This makes the garage a versatile space. Bicycles, garden tools and tools can be stored. Small repairs to cart, bike and lawn mower can be done here.

The problem is common: The old garage floor has become crumbly. There, where the four tires of the car are, there are holes in the ground. In rain and snow, small puddles form. The paint with concrete paint does not last long on this surface either. If you sweep the garage, you are in a cloud of dust without having properly disposed of the dirt.

A really long-term solution to this problem can be achieved when you use ceramic tiles on a garage floor. Although this is more time-consuming at the moment than repairing the old floor and painting it with a new coat of paint, it’s worth it in the long run.

Tiles are more expensive than concrete color. This is true, but considering that the not just cheap concrete paint has to be renewed often, the simple solution can be even more expensive. Very often in the hardware stores cheap tiles are offered, which are ideal for this purpose. The workload is significantly lower in the long run when you use ceramic tiles on a garage floor.

The tile floor is more durable. The ongoing cleaning of the garage from dust, leaves, rain and winter slush is less time consuming. Oil stains from the vehicle and the lawn mower repair are easy to remove. You win a room that you like to use as a small workshop additionally.

Use ceramic tiles on a garage floor: choice of the right tile

Split plates are very hard and insensitive to pressure. Due to their dense structure, they are impermeable to water and therefore frost-proof. They are glazed or unglazed. For the garage only unglazed stoneware tiles come into question. A glaze would be damaged in a short time and rubbed off.

The car carries sand and dirt into the garage. The tires would act on the surface during braking and starting like sandpaper. It is unavoidable that the garage floor is damp by the rain wet vehicle. In winter, the slush thaws out of the wheel arches.

Glazed surfaces would be very slippery under these conditions. Of course, if the garage is not heated, which is usually the case today, the tiles must of course be frost-proof and frost-proof. This must also be considered in the preparation of the underground.

Due to the size of the area to be tiled and the high temperature fluctuations, expansion joints should be planned during installation, which will later be filled permanently elastic.

Old or new surface?

If a garage floor is covered with tiles, the surface makes no problems. But old, damaged concrete floor must be well prepared first. Loose concrete paint must be scraped off with the spatula. Holes must be repaired with repair mortar to create a flat surface. A primer in the form of an emulsion binds the dust and improves the adhesion of the tiled surface to the substrate.

Ideally, the garage floor should have a slight slope to the gate, so that dripping rainwater and thawing snow do not remain on the ground. A self-leveling compound, which is poured out on the entire floor and easily distributed, can remedy this situation.

The garage is measured and then drawn a laying plan. The expansion joints are drawn. The course of the tile dressing is previously calculated precisely to obtain a uniform laying pattern. The individual work sections are divided.

The laying plan is now transferred to the garage floor with the help of the guideline. Guides are recorded both longitudinally and transversely on the garage floor. The course of the laying pattern is marked, as well as the position of the expansion joints.

Laying the tiles

The glue can be mixed after this preparation work. It is mixed as much glue as can be consumed in the processing time of 2 hours. The information on the packaging must be observed. Each glue needs after maturing a maturation time of about 15 minutes to develop its full effectiveness. Thereafter, it is vigorously mixed again.

In some jobs the adhesive is combed thicker. The spatula has a toothing of 8 mm. This can be used to compensate for small bumps without the tile being hollow or in direct contact with the ground.

If the tile back is heavily textured, glue must also be applied thinly and over the entire surface on the back of the tile. In the case of the high pressure load in the garage, a 100% void-free installation must be guaranteed, otherwise the tiles would break.

The beginning and end tiles are pressed into the moist adhesive bed and connected to the tile witch. Along the guideline, the first row is laid longitudinally to the wall. The following series are in the ship’s association, d. H. always offset to one another half, laid. With the rubber hammer, each tile is easily tapped.

The orientation of the tiles to each other and the horizontal are checked in sections with the guideline and the spirit level in order to be able to correct in the open time. Even with the use of tile crosses, the alignment must be checked with the guideline, since not all tiles are absolutely the same size.

The base tiles are set in the buttering process. The tile adhesive is only fully combed on the back of the tile. In order to maintain a uniform expansion gap between wall and floor, a correspondingly thick wooden strip is laid on the ground and the base tile laid flush on this spacer and lightly tapped with the rubber hammer. Finished.

How to Choose Tiles, Glue and Tools

For little money you often get leftovers or opened packaging units. Also, the glue consumption in the middle bed process is considerably greater. This must be taken into account when purchasing.

On the packaging, the consumption per m2 is indicated when using different thickness toothpicks. The split tiles are thicker and harder than normal wall tiles. When buying the tile cutter this must be considered, because only with a strong device, these tiles can be cut.

  • The split plates are designed for the sample. This is particularly important in this case, as the tiles are to be laid in the dressing.
  • Applying the adhesive over the entire area in the middle bed process. The notched trowel has a serration of 8 mm.
  • The tile witch, two tiling corners connected with a guideline, is stretched between the first and the last tile.
  • Joint distances between the individual tiles are precisely maintained by the tile crosses.
  • Bleed tiles are measured in sections and marked with a pencil on the top.
  • The tile cutter is indispensable when laying large areas. The tiles are precisely scratched and broken.
  • The tiles are laid in association. The first row is laid longitudinally to the wall, the second half offset from one another.
  • The adhesive bed must be full-surface and moist to ensure 100% void-free bonding.
  • The base tiles are set in the buttering process. The adhesive mortar is applied to the back of the tile.
  • For heavy loads on a garage floor, the panels must be laid with the right adhesive.